Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
How do you actually feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard task. If the old tub is conveniently accessible, the project can relocate speedily; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This article will assist you mount a brand-new bathtub in your restroom if you have actually already acquired a new tub and also do not need to change the plan of your previous water pipelines.
Your devices and material checklist must consist of the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub up until the spirit level reviews level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow outlet as well as the normal outlet for leakages.
Lastly, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the tub has actually been used a minimum of once as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about Installing A Bathtub, I think sharing that section was essential. Kindly take the time to distribute this article if you enjoyed it. I recognize the value of reading our article about How to Install a Bathtub.
Visit My Site Report this page